Manpages - vgcfgrestore.8

vgcfgrestore — Restore volume group configuration

vgcfgrestore option_args position_args
[ option_args ]
[ position_args ]

–commandprofile String
–config String
-d*|–debug*
–devices PV
–devicesfile String
–driverloaded y*|*n
-f*|–file* String
–force
-h*|–help*
–journal String
-l*|–list*
–lockopt String
–longhelp
-M*|–metadatatype* lvm2
–nohints
–nolocking
–profile String
-q*|–quiet*
-t*|–test*
-v*|–verbose*
–version
-y*|–yes*

vgcfgrestore restores the metadata of a VG from a text back up file produced by vgcfgbackup. This writes VG metadata onto the devices specifed in back up file.

A back up file can be specified with –file. If no backup file is specified, the most recent one is used. Use –list for a list of the available back up and archive files of a VG.

WARNING: When a VG contains thin pools, changes to thin metadata cannot be reverted, and data loss may occur if thin metadata has changed. The force option is required to restore in this case.

Restore VG metadata from last backup.

vgcfgrestore VG

[ COMMON_OPTIONS ]

—

Restore VG metadata from specified file.

vgcfgrestore -f*|–file* String VG

[ COMMON_OPTIONS ]

—

List all VG metadata backups.

vgcfgrestore -l*|–list* VG

[ COMMON_OPTIONS ]

—

List one VG metadata backup file.

vgcfgrestore -l*|–list* -f*|–file* String

[ COMMON_OPTIONS ]

[ VG ]

—

Common options for command:

[ -M*|–metadatatype* lvm2 ]
[ –force ]

Common options for lvm:

[ -d*|–debug* ]
[ -h*|–help* ]
[ -q*|–quiet* ]
[ -t*|–test* ]
[ -v*|–verbose* ]
[ -y*|–yes* ]
[ –commandprofile String ]
[ –config String ]
[ –devices PV ]
[ –devicesfile String ]
[ –driverloaded y*|*n ]
[ –journal String ]
[ –lockopt String ]
[ –longhelp ]
[ –nohints ]
[ –nolocking ]
[ –profile String ]
[ –version ]

–commandprofile String
The command profile to use for command configuration. See *lvm.conf*(5) for more information about profiles.

–config String
Config settings for the command. These override *lvm.conf*(5) settings. The String arg uses the same format as *lvm.conf*(5), or may use section/field syntax. See *lvm.conf*(5) for more information about config.

-d*|–debug* …
Set debug level. Repeat from 1 to 6 times to increase the detail of messages sent to the log file and/or syslog (if configured).

–devices PV
Devices that the command can use. This option can be repeated or accepts a comma separated list of devices. This overrides the devices file.

–devicesfile String
A file listing devices that LVM should use. The file must exist in etc/lvm/devices and is managed with the lvmdevices*(8) command. This overrides the *lvm.conf*(5) *devices/devicesfile and devices/use_devicesfile settings.

–driverloaded y*|*n
If set to no, the command will not attempt to use device-mapper. For testing and debugging.

-f*|–file* String
Read metadata backup from the named file. Usually this file was created by vgcfgbackup.

–force …
Force metadata restore even with thin pool LVs. Use with extreme caution. Most changes to thin metadata cannot be reverted. You may lose data if you restore metadata that does not match the thin pool kernel metadata precisely.

-h*|–help*
Display help text.

–journal String
Record information in the systemd journal. This information is in addition to information enabled by the lvm.conf log/journal setting. command: record information about the command. output: record the default command output. debug: record full command debugging.

-l*|–list*
List metadata backup and archive files pertaining to the VG. May be used with –file. Does not restore the VG.

–lockopt String
Used to pass options for special cases to lvmlockd. See *lvmlockd*(8) for more information.

–longhelp
Display long help text.

-M*|–metadatatype* lvm2
Specifies the type of on-disk metadata to use. lvm2 (or just 2) is the current, standard format. lvm1 (or just 1) is no longer used.

–nohints
Do not use the hints file to locate devices for PVs. A command may read more devices to find PVs when hints are not used. The command will still perform standard hint file invalidation where appropriate.

–nolocking
Disable locking.

–profile String
An alias for –commandprofile or –metadataprofile, depending on the command.

-q*|–quiet* …
Suppress output and log messages. Overrides –debug and –verbose. Repeat once to also suppress any prompts with answer ’no’.

-t*|–test*
Run in test mode. Commands will not update metadata. This is implemented by disabling all metadata writing but nevertheless returning success to the calling function. This may lead to unusual error messages in multi-stage operations if a tool relies on reading back metadata it believes has changed but hasn’t.

-v*|–verbose* …
Set verbose level. Repeat from 1 to 4 times to increase the detail of messages sent to stdout and stderr.

–version
Display version information.

-y*|–yes*
Do not prompt for confirmation interactively but always assume the answer yes. Use with extreme caution. (For automatic no, see -qq.)

VG

Volume Group name. See *lvm*(8) for valid names.

String

See the option description for information about the string content.

Size[UNIT]

Size is an input number that accepts an optional unit. Input units are always treated as base two values, regardless of capitalization, e.g. ’k’ and ’K’ both refer to 1024. The default input unit is specified by letter, followed by |UNIT. UNIT represents other possible input units: b*|*B is bytes, s*|*S is sectors of 512 bytes, k*|*K is KiB, m*|*M is MiB, g*|*G is GiB, t*|*T is TiB, p*|*P is PiB, e*|*E is EiB. (This should not be confused with the output control –units, where capital letters mean multiple of 1000.)

See *lvm*(8) for information about environment variables used by lvm. For example, LVM_VG_NAME can generally be substituted for a required VG parameter.

To replace PVs, vgdisplay –partial –verbose will show the UUIDs and sizes of any PVs that are no longer present. If a PV in the VG is lost and you wish to substitute another of the same size, use pvcreate –restorefile filename –uuid uuid (plus additional arguments as appropriate) to initialise it with the same UUID as the missing PV. Repeat for all other missing PVs in the VG. Then use vgcfgrestore –file filename to restore the VG’s metadata.

*lvm*(8), *lvm.conf*(5), *lvmconfig*(8), *lvmdevices*(8),

*pvchange*(8), *pvck*(8), *pvcreate*(8), *pvdisplay*(8), *pvmove*(8), *pvremove*(8), *pvresize*(8), *pvs*(8), *pvscan*(8),

*vgcfgbackup*(8), *vgcfgrestore*(8), *vgchange*(8), *vgck*(8), *vgcreate*(8), *vgconvert*(8), *vgdisplay*(8), *vgexport*(8), *vgextend*(8), *vgimport*(8), *vgimportclone*(8), *vgimportdevices*(8), *vgmerge*(8), *vgmknodes*(8), *vgreduce*(8), *vgremove*(8), *vgrename*(8), *vgs*(8), *vgscan*(8), *vgsplit*(8),

*lvcreate*(8), *lvchange*(8), *lvconvert*(8), *lvdisplay*(8), *lvextend*(8), *lvreduce*(8), *lvremove*(8), *lvrename*(8), *lvresize*(8), *lvs*(8), *lvscan*(8),

*lvm-fullreport*(8), *lvm-lvpoll*(8), *lvm2-activation-generator*(8), *blkdeactivate*(8), *lvmdump*(8),

*dmeventd*(8), *lvmpolld*(8), *lvmlockd*(8), *lvmlockctl*(8), *cmirrord*(8), *lvmdbusd*(8), *fsadm*(8),

*lvmsystemid*(7), *lvmreport*(7), *lvmraid*(7), *lvmthin*(7), *lvmcache*(7)