Manpages - sg_rep_zones.8

sg_rep_zones - send SCSI REPORT ZONES, REALMS or ZONE DOMAINS command

sg_rep_zones [/–domain/] [/–help/] [/–hex/] [/–inhex=FN/] [/–locator=LBA/] [/–maxlen=LEN/] [/–num=NUM/] [/–partial/] [/–raw/] [/–readonly/] [/–realm/] [/–report=OPT/] [/–start=LBA/] [/–verbose/] [/–version/] [/–wp/] DEVICE

Sends a SCSI REPORT ZONES, REPORT REALMS or REPORT ZONE DOMAINS command to DEVICE and decodes (or simply outputs) the data returned. These commands is found in the ZBC-2 draft standard, revision 10 (zbc2r05.pdf). Only the REPORT ZONES command is defined in the original ZBC standard (INCITS 536-2017) and it is the default.

The REPORT ZONE DOMAINS command will be sent (or decoded) when the –domain option is given. The REPORT REALMS command will be sent (or decoded) when the –realm option is given.

Rather than send a SCSI command to DEVICE, if the –inhex=FN option is given, then the contents of the file named FN are decoded as ASCII hex (or binary if –raw is also given) and then processed as if it was the response of the command. By default the REPORT ZONES command response is assumed; if the –domain or –realm option is given then the corresponding command response is assumed.

Arguments to long options are mandatory for short options as well.

-d, –domain

send or decode the SCSI REPORT ZONE DOMAINS command.

-h, –help

output the usage message then exit.

-H, –hex

output the response in hexadecimal to stdout. When used once the whole response is output in ASCII hexadecimal with a leading address (starting at 0) on each line. When used twice each zone descriptor in the response is output separately in hexadecimal. When used thrice the whole response is output in hexadecimal with no leading address (on each line).
The output format when this option is given thrice is suitable contents for a later invocation with the –inhex=FN option.

-i, *–inhex*=/FN/

where FN is a file name whose contents are assumed to be ASCII hexadecimal. If DEVICE is also given then DEVICE is ignored, a warning is issued and the utility continues, decoding the file named FN. See the “FORMAT OF FILES CONTAINING ASCII HEX” section in the sg3_utils manpage for more information. If the –raw option is also given then the contents of FN are treated as binary.
Note that by default this utility assumes then contents are the response from a REPORT ZONES command. Use the –domain or –realm option for decoding the other two commands.

-l, *–locator*=/LBA/

where LBA plays a similar role as it does in –start=LBA. It is the field name used in the REPORT REALMS and REPORT ZONE DOMAINS commands.

-m, *–maxlen*=/LEN/

where LEN is the (maximum) response length in bytes. It is placed in the cdb’s “allocation length” field. If not given (or LEN is zero) then 8192 is used. The maximum allowed value of LEN is 1048576.

-n, *–num*=/NUM/

where NUM is the (maximum) number of zone descriptors to print out. The default value is zero which is taken to mean print out all zone descriptors returned by the REPORT ZONES command.

-p, –partial

set the PARTIAL bit in the cdb.

-r, –raw

output response in binary (to stdout) unless the –inhex=FN option is also given. In that case the input file name (FN) is decoded as binary (and the output is not in binary (but may be hex)).

-R, –readonly

open the DEVICE read-only (e.g. in Unix with the O_RDONLY flag). The default is to open it read-write.

-e, –realm

send or decode the SCSI REPORT REALMS command.

-o, *–report*=/OPT/

where OPT will become the contents of the REPORTING OPTION field in the cdb. The reporting options differ between REPORT ZONES, REPORT ZONE DOMAINS and REPORT REALMS. If the –help option is given twice ( or the equivalent ’-hh’) a list of available reporting options (as of writing) for each command is output.
The default value for REPORT ZONES is 0 which means report a list of all zones. Some other values are 1 for list zones with a zone condition of empty; 2 for list zones with a zone condition of implicitly opened; 3 for list zones with a zone condition of explicitly opened; 4 for list zones with a zone condition of closed; 5 for list zones with a zone condition of full; 6 for list zones with a zone condition of read only; 7 for list zones with a zone condition of offline. Other values are 0x10 for list zones with ’RWP recommended’ set to true; 0x11 for list zones with non-sequential write resource active set to true and 0x3f for list zones with a zone condition of ’not write pointer’.

-s, *–start*=/LBA/

where LBA is at the start or within the first zone to be reported. The default value is 0. If LBA is not a zone start LBA then the preceding zone start LBA is used for reporting. Assumed to be in decimal unless prefixed with ’0x’ or has a trailing ’h’ which indicate hexadecimal.
The zone start LBA field used in the REPORT ZONES command was changed to the zone domain/realm locator field for the two newer ZBC-2 commands. For this utility –locator=LBA and –start=LBA are interchangeable.

-v, –verbose

increase the level of verbosity, (i.e. debug output).

-V, –version

print the version string and then exit.

-w, –wp

print the write pointer (in hex) only. In the absence of errors, then a hex LBA will be printed on each line, one line for each zone. Can be usefully combined with the –num=NUM and –start=LBA options.

The exit status of sg_rep_zones is 0 when it is successful. Otherwise see the sg3_utils(8) man page.

Written by Douglas Gilbert.

Report bugs to <dgilbert at interlog dot com>.

Copyright © 2014-2021 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

sg_reset_wp,sg_zone(sg3_utils)