Manpages - zmq_udp.7

zmq_udp - 0MQ UDP multicast and unicast transport

UDP is unreliable protocol transport of data over IP networks. UDP support both unicast and multicast communication.

UDP transport can only be used with the ZMQ_RADIO and ZMQ_DISH socket types.

A 0MQ endpoint is a string consisting of a transport:// followed by an address. The transport specifies the underlying protocol to use. The address specifies the transport-specific address to connect to.

For the UDP transport, the transport is udp. The meaning of the address part is defined below.

Binding a socket

    With udp we can only bind the ZMQ_DISH socket type.
    When binding a socket using _zmq_bind()_ with the udp
    transport the endpoint shall be interpreted as an interface followed by a
    colon and the UDP port number to use.

    An interface may be specified by either of the following:

    * The wild-card `*`, meaning all available interfaces.
    * The name of the network interface (i.e. eth0, lo, wlan0 etc...)
    * The primary address assigned to the interface, in its numeric representation.
    * Multicast address in its numeric representation the socket should join.

    The UDP port number may be specified a numeric value, usually above
    1024 on POSIX systems.

    Connecting a socket

With udp we can only connect the ZMQ_RADIO socket type. When connecting a socket to a peer address using zmq_connect() with the udp transport, the endpoint shall be interpreted as a peer address followed by a colon and the UDP port number to use.

A peer address may be specified by either of the following:

·

The IPv4 or IPv6 address of the peer, in its numeric representation or using its hostname.

·

Multicast address in its numeric representation.

Binding a socket.

    //  Unicast - UDP port 5555 on all available interfaces
    rc = zmq_bind(dish, "udp://*:5555");
    assert (rc == 0);
    //  Unicast - UDP port 5555 on the local loop-back interface
    rc = zmq_bind(dish, "udp://127.0.0.1:5555");
    assert (rc == 0);
    //  Unicast - UDP port 5555 on interface eth1
    rc = zmq_bind(dish, "udp://eth1:5555");
    assert (rc == 0);
    //  Multicast - UDP port 5555 on a Multicast address
    rc = zmq_bind(dish, "udp://239.0.0.1:5555");
    assert (rc == 0);
    //  Same as above but joining only on interface eth0
    rc = zmq_bind(dish, "udp://eth0;239.0.0.1:5555");
    assert (rc == 0);
    //  Same as above using IPv6 multicast
    rc = zmq_bind(dish, "udp://eth0;[ff02::1]:5555");
    assert (rc == 0);

Connecting a socket.

    //  Connecting using an Unicast IP address
    rc = zmq_connect(radio, "udp://192.168.1.1:5555");
    assert (rc == 0);
    //  Connecting using a Multicast address
    rc = zmq_connect(socket, "udp://239.0.0.1:5555);
    assert (rc == 0);
    //  Connecting using a Multicast address using local interface wlan0
    rc = zmq_connect(socket, "udp://wlan0;239.0.0.1:5555);
    assert (rc == 0);
    //  Connecting to IPv6 multicast
    rc = zmq_connect(socket, "udp://[ff02::1]:5555);
    assert (rc == 0);

*zmq_connect*(3) *zmq_setsockopt*(3) *zmq_tcp*(7) *zmq_ipc*(7) *zmq_inproc*(7) *zmq_vmci*(7) *zmq*(7)

This page was written by the 0MQ community. To make a change please read the 0MQ Contribution Policy at http://www.zeromq.org/docs:contributing.