Manpages - socketpair.3p

This manual page is part of the POSIX Programmer’s Manual. The Linux implementation of this interface may differ (consult the corresponding Linux manual page for details of Linux behavior), or the interface may not be implemented on Linux.

socketpair — create a pair of connected sockets

  #include <sys/socket.h>
  int socketpair(int domain, int type, int protocol,
      int socket_vector[2]);

The socketpair/() function shall create an unbound pair of connected sockets in a specified /domain, of a specified type, under the protocol optionally specified by the protocol argument. The two sockets shall be identical. The file descriptors used in referencing the created sockets shall be returned in socket_vector[0] and socket_vector[1]. The file descriptors shall be allocated as described in Section 2.14, File Descriptor Allocation.

The /socketpair/() function takes the following arguments:

domain

Specifies the communications domain in which the sockets are to be created.

type

Specifies the type of sockets to be created.

protocol

Specifies a particular protocol to be used with the sockets. Specifying a protocol of 0 causes /socketpair/() to use an unspecified default protocol appropriate for the requested socket type.

socket_vector

Specifies a 2-integer array to hold the file descriptors of the created socket pair.

The type argument specifies the socket type, which determines the semantics of communications over the socket. The following socket types are defined; implementations may specify additional socket types:

SOCK_STREAM

Provides sequenced, reliable, bidirectional, connection-mode byte streams, and may provide a transmission mechanism for out-of-band data.

SOCK_DGRAM

Provides datagrams, which are connectionless-mode, unreliable messages of fixed maximum length.

SOCK_SEQPACKET

Provides sequenced, reliable, bidirectional, connection-mode transmission paths for records. A record can be sent using one or more output operations and received using one or more input operations, but a single operation never transfers part of more than one record. Record boundaries are visible to the receiver via the MSG_EOR flag.

If the protocol argument is non-zero, it shall specify a protocol that is supported by the address family. If the protocol argument is zero, the default protocol for this address family and type shall be used. The protocols supported by the system are implementation-defined.

The process may need to have appropriate privileges to use the /socketpair/() function or to create some sockets.

Upon successful completion, this function shall return 0; otherwise, -1 shall be returned and errno set to indicate the error, no file descriptors shall be allocated, and the contents of socket_vector shall be left unmodified.

The /socketpair/() function shall fail if:

EAFNOSUPPORT

The implementation does not support the specified address family.

EMFILE

All, or all but one, of the file descriptors available to the process are currently open.

ENFILE

No more file descriptors are available for the system.

EOPNOTSUPP

The specified protocol does not permit creation of socket pairs.

EPROTONOSUPPORT

The protocol is not supported by the address family, or the protocol is not supported by the implementation.

EPROTOTYPE

The socket type is not supported by the protocol.

The /socketpair/() function may fail if:

EACCES

The process does not have appropriate privileges.

ENOBUFS

Insufficient resources were available in the system to perform the operation.

ENOMEM

Insufficient memory was available to fulfill the request.

The following sections are informative.

None.

The documentation for specific address families specifies which protocols each address family supports. The documentation for specific protocols specifies which socket types each protocol supports.

The /socketpair/() function is used primarily with UNIX domain sockets and need not be supported for other domains.

None.

None.

Section 2.14, File Descriptor Allocation, /socket ( )/

The Base Definitions volume of POSIX.1‐2017, <sys_socket.h>

Portions of this text are reprinted and reproduced in electronic form from IEEE Std 1003.1-2017, Standard for Information Technology – Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 7, 2018 Edition, Copyright (C) 2018 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between this version and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html .

Any typographical or formatting errors that appear in this page are most likely to have been introduced during the conversion of the source files to man page format. To report such errors, see https://www.kernel.org/doc/man-pages/reporting_bugs.html .