Manpages - zmq_msg_send.3

zmq_msg_send - send a message part on a socket

int zmq_msg_send (zmq_msg_t */*msg/, void *socket, int flags);*

The zmq_msg_send() function is identical to *zmq_sendmsg*(3), which shall be deprecated in future versions. zmq_msg_send() is more consistent with other message manipulation functions.

The zmq_msg_send() function shall queue the message referenced by the msg argument to be sent to the socket referenced by the socket argument. The flags argument is a combination of the flags defined below:

ZMQ_DONTWAIT

For socket types (DEALER, PUSH) that block (either with ZMQ_IMMEDIATE option set and no peer available, or all peers having full high-water mark), specifies that the operation should be performed in non-blocking mode. If the message cannot be queued on the socket, the zmq_msg_send() function shall fail with errno set to EAGAIN.

ZMQ_SNDMORE

Specifies that the message being sent is a multi-part message, and that further message parts are to follow. Refer to the section regarding multi-part messages below for a detailed description.

The zmq_msg_t structure passed to zmq_msg_send() is nullified on a successful call. If you want to send the same message to multiple sockets you have to copy it (e.g. using zmq_msg_copy()). If the call fails, the zmq_msg_t structure stays intact, and must be consumed by another call to zmq_msg_send() on the same or another socket, or released using zmq_msg_close() to avoid a memory leak.

Note

A successful invocation of zmq_msg_send() does not indicate that the message has been transmitted to the network, only that it has been queued on the socket and 0MQ has assumed responsibility for the message. You do not need to call zmq_msg_close() after a successful zmq_msg_send().

The zmq_msg_send() function shall return number of bytes in the message if successful (if number of bytes is higher than MAX_INT, the function will return MAX_INT). Otherwise it shall return -1 and set errno to one of the values defined below.

EAGAIN

Non-blocking mode was requested and the message cannot be sent at the moment.

ENOTSUP

The zmq_msg_send() operation is not supported by this socket type.

EINVAL

The sender tried to send multipart data, which the socket type does not allow.

EFSM

The zmq_msg_send() operation cannot be performed on this socket at the moment due to the socket not being in the appropriate state. This error may occur with socket types that switch between several states, such as ZMQ_REP. See the messaging patterns section of *zmq_socket*(3) for more information.

ETERM

The 0MQ context associated with the specified socket was terminated.

ENOTSOCK

The provided socket was invalid.

EINTR

The operation was interrupted by delivery of a signal before the message was sent.

EFAULT

Invalid message.

EHOSTUNREACH

The message cannot be routed.

Filling in a message and sending it to a socket.

    /* Create a new message, allocating 6 bytes for message content */
    zmq_msg_t msg;
    int rc = zmq_msg_init_size (&msg, 6);
    assert (rc == 0);
    /* Fill in message content with AAAAAA */
    memset (zmq_msg_data (&msg), A, 6);
    /* Send the message to the socket */
    rc = zmq_msg_send (&msg, socket, 0);
    assert (rc == 6);

Sending a multi-part message.

    /* Send a multi-part message consisting of three parts to socket */
    rc = zmq_msg_send (&part1, socket, ZMQ_SNDMORE);
    rc = zmq_msg_send (&part2, socket, ZMQ_SNDMORE);
    /* Final part; no more parts to follow */
    rc = zmq_msg_send (&part3, socket, 0);

*zmq_recv*(3) *zmq_send*(3) *zmq_msg_recv*(3) *zmq_socket*(7) *zmq*(7)

This page was written by the 0MQ community. To make a change please read the 0MQ Contribution Policy at http://www.zeromq.org/docs:contributing.