Manpages - echo.1p

This manual page is part of the POSIX Programmer’s Manual. The Linux implementation of this interface may differ (consult the corresponding Linux manual page for details of Linux behavior), or the interface may not be implemented on Linux.

echo — write arguments to standard output

  echo [string...]

The echo utility writes its arguments to standard output, followed by a <newline>. If there are no arguments, only the <newline> is written.

The echo utility shall not recognize the “–” argument in the manner specified by Guideline 10 of the Base Definitions volume of POSIX.1‐2017, Section 12.2, Utility Syntax Guidelines; “–” shall be recognized as a string operand.

Implementations shall not support any options.

The following operands shall be supported:

string

A string to be written to standard output. If the first operand is -n, or if any of the operands contain a <backslash> character, the results are implementation-defined.

On XSI-conformant systems, if the first operand is -n, it shall be treated as a string, not an option. The following character sequences shall be recognized on XSI-conformant systems within any of the arguments:

\a

Write an <alert>.

\b

Write a <backspace>.

\c

Suppress the <newline> that otherwise follows the final argument in the output. All characters following the ’\c’ in the arguments shall be ignored.

\f

Write a <form-feed>.

\n

Write a <newline>.

\r

Write a <carriage-return>.

\t

Write a <tab>.

\v

Write a <vertical-tab>.

\\

Write a <backslash> character.

\0num

Write an 8-bit value that is the zero, one, two, or three-digit octal number num.

Not used.

None.

The following environment variables shall affect the execution of echo:

LANG

Provide a default value for the internationalization variables that are unset or null. (See the Base Definitions volume of POSIX.1‐2017, Section 8.2, Internationalization Variables for the precedence of internationalization variables used to determine the values of locale categories.)

LC_ALL

If set to a non-empty string value, override the values of all the other internationalization variables.

LC_CTYPE

Determine the locale for the interpretation of sequences of bytes of text data as characters (for example, single-byte as opposed to multi-byte characters in arguments).

LC_MESSAGES

Determine the locale that should be used to affect the format and contents of diagnostic messages written to standard error.

NLSPATH

Determine the location of message catalogs for the processing of LC_MESSAGES.

Default.

The echo utility arguments shall be separated by single <space> characters and a <newline> character shall follow the last argument. Output transformations shall occur based on the escape sequences in the input. See the OPERANDS section.

The standard error shall be used only for diagnostic messages.

None.

None.

The following exit values shall be returned:

 0

Successful completion.

>0

An error occurred.

Default.

The following sections are informative.

It is not possible to use echo portably across all POSIX systems unless both -n (as the first argument) and escape sequences are omitted.

The printf utility can be used portably to emulate any of the traditional behaviors of the echo utility as follows (assuming that IFS has its standard value or is unset):

*

The historic System V echo and the requirements on XSI implementations in this volume of POSIX.1‐2017 are equivalent to:

      printf "%b\n$*"

*

The BSD echo is equivalent to:

      if [ "X$1" = "X-n" ]
      then
          shift
          printf "%s$*"
      else
          printf "%s\n$*"
      fi

New applications are encouraged to use printf instead of echo.

None.

The echo utility has not been made obsolescent because of its extremely widespread use in historical applications. Conforming applications that wish to do prompting without <newline> characters or that could possibly be expecting to echo a -n, should use the printf utility derived from the Ninth Edition system.

As specified, echo writes its arguments in the simplest of ways. The two different historical versions of echo vary in fatally incompatible ways.

The BSD echo checks the first argument for the string -n which causes it to suppress the <newline> that would otherwise follow the final argument in the output.

The System V echo does not support any options, but allows escape sequences within its operands, as described for XSI implementations in the OPERANDS section.

The echo utility does not support Utility Syntax Guideline 10 because historical applications depend on echo to echo all of its arguments, except for the -n option in the BSD version.

None.

/printf /

The Base Definitions volume of POSIX.1‐2017, Chapter 8, Environment Variables, Section 12.2, Utility Syntax Guidelines

Portions of this text are reprinted and reproduced in electronic form from IEEE Std 1003.1-2017, Standard for Information Technology – Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 7, 2018 Edition, Copyright (C) 2018 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between this version and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html .

Any typographical or formatting errors that appear in this page are most likely to have been introduced during the conversion of the source files to man page format. To report such errors, see https://www.kernel.org/doc/man-pages/reporting_bugs.html .